欢迎光临梯瑞卡流体控制设备（四川）有限公司！
Chinese
欢迎光临梯瑞卡流体控制设备（四川）有限公司！
Chinese
| Dyna-Star HP and HF Lubrication Pump | |
Metric | |
| Maximum Fluid Working Pressure | |
| HF Models | 24.1 MPa, 241 bar |
| HP Models | 34.47 MPa, 344 bar |
| Electrical Requirements | |
| All Models | 24VDC |
| Wire Terminal AWG Size for Control Board | 24 to 10 AWG |
| Input Voltage Range | |
| 24 VDC | 18 to 32 VDC |
| ON/OFF Signal Voltage Range and Current | |
| Voltage Range | 5 to 32 VDC |
| Drive Resistance | 1.1K |
| Peak Operating Current | |
| 24 VDC | 35A |
| Peak Power | |
| 24 VDC | 720W |
| Pump Output | |
| HF Models | See Performance Charts in manual |
| HP Models | See Performance Charts in manual |
| Weight - Pump Only | |
| 35 - 60 lb Tank / Reservoir | 22.7 kg |
| 90 - 120 lb Tank / Reservoir | 25.0 kg |
| 400 lb Tank / Reservoir | 27.2 kg |
| Wetted Parts | |
| Pump Wetted Parts | steel, polyurethane, acetal, buna-N, aluminum, polyester elastomer |
| Operating Temperature | |
| HP Models | –40° to 65°C |
| HF Models | -10° to 65°C |
| Storage Temperature HP and HF Models | –40° to 65°C |
| Humidity Level | 90% |
| IP Rating | IP69K |
| Audible Sound Pressure* | |
| 1000 psi (6.89 MPa, 58.95 bar) Models | 70.7 dB(A) |
| 2000 psi (13.79 MPa, 137.9 bar) Models | 71.4 dB(A) |
| 3000 psi (20.68 MPa, 206.84 bar) Models | 71.4 dB(A) |
| 4000 psi (27.58 MPa, 275.79 bar) Models | 71.2 dB(A) |
| 5000 psi (34.47 MPa, 374.74 bar) Models | 70.6 dB(A) |
| Cable | |
| Cable Gland Thread | M25 |
| Cable Range | 9 - 16 cm |
| *Sound power was measured per ISO-9614-2. | |
| Dyna-Star® HP Vent Valve Kit | |
| Maximum working pressure* | 24.1 MPa, 241 bar |
| *Dyna-Star HP Pump models are rated for 5000 psi (34.47 MPa, 344 bar) maximum working pressure, however, when a vent valve is installed on the HP pump, the maximum working pressure must be reduced to 3500 psi (24.1 MPa, 241 bar). | |
| Inlet/Outlet Sizes | |
| Outlet (marked “0”) | 3/8 in. NPT(f) |
| Inlet (refill-marked “1”) | 3/8 in. NPT(f) |
| Pressure Relief Valve | |
| Factory set pressure | 27 MPA, 275 bar ± 10% |
| Reset pressure | 80% of set pressure |
| Relief Rate (Flow capability depends on viscosity, type of fluid, temperature, etc.) | 0.4 liters/minute @ 24.1 MPa, 241 bar |
| Solenoid Valve | |
| Flow (Flow capability depends on viscosity, type of fluid, temperature, etc.) | 0.65 liters /minute |
| Wetted parts | zinc plated steel, carbon steel, aluminum, fluoroelastomer, polyurethane |
| Weight | 1.8 kg |
| IP rating | IP65K |
| Solenoid Coil: Resistance (DC) (Ohms) | @20°C |
| 24 VDC | 0.83 |
| Auto-Fill Shutoff Valve for Dyna-Star® HP or HF Pump | |
| Maximum working pressure* | 34.4 MPa, 344 bar |
| Inlet/Outlet Sizes | |
| Outlet (marked “0”) | 3/8 in. NPT(f) |
| Inlet (refill-marked “1”) | 3/8 in. NPT(f) |
| Maximum flow | 7.6 liters/minute |
| Wetted Parts | |
| Valve | neoprene rubber, zinc plated parts, stainless steel, chrome plated pats, plastic acetal |
| Seal | fluorocarbon |
| Temperature | |
| Working temperature | -25°C to 50°C |
| Dyna-Star® HP Pump System | |
| Maximum working pressure* | 241 bar, 24.1 MPa |
| *Dyna-Star HP pump models are rated for a maximum working pressure of 5000 psi (344 bar, 34.47 MPa), however, when a vent valve is installed on the HP pump, the maximum working pressure must be reduced to 3500 psi (344 bar, 34.47 MPa). | |
| Reservoir overflow port size | 1/2 inch NPT |
| Reservoir fill port size | 1/2 inch NPT |
| Lubricant outlet port size | 3/8 inch NPT(f) |
| Reservoir wetted parts | steel, buna-n rubber |
| Pump wetted parts | See manual 332514, Dyna-Star HP and HF Pump |
| Vent Valve wetted part | See manual 332519, Dyna-Star HP and HF Vent Valve Kit |
| Grease Capacity | |
| Models 77X101, 77X103, 77X105 | 41 kg |
| Models 77X100, 77X102, 77X104 | 27 kg |
| Sound Data | |
| All pumps | See manual 332514, Dyna-Star HP and HF Pump |
| Dyna-Star® HP or HF Pump Low Level Indicator Kit; Dip Stick Kit | |
| Low Level Indicator | |
| Low level sensor switch | Normally open sensor switch; closes upon low level |
| Operating temperature range | -45°C to 65°C |
| Switching power | 10 Watt Max. |
| Switching current | 0.4A-Max. |
| Switching voltage | 5 to 32 VDC |
| Contact resistance | 0.150 Ohms-Max. |
| Body thread | 3/4 inch NPT(m) |
| Wetted parts | |
| Cable | nylon coated stainless steel |
| Crimp tab | stainless steel |
| Dip Stick | |
| Body thread | 3/4 inch NPT(m) |
| Wetted parts | zinc plated steel |
| Fill Valve | |
| Maximum fluid working pressure | 34.4 MPa, 344.7 bar |
| Relief value | 34.4 MPa, 344.7 bar ± 10% |
| Maximum fluid flow | 7.57 liters per minute |
| Outlet port size | 3/4 inch NPT |
| Vent port size | 3/8 inch NPT |
| Inlet | ISO 7241–1, Series B standard hydraulic quick disconnect, 1/4 inch coupling |
| Wetted parts | Parts: zinc plated steel parts; Seals: Buna-N |
| Weight | |
